Registration Dossier

Diss Factsheets

Administrative data

First-aid measures

· General information: Immediately remove any clothing soiled by the product.

· After inhalation: Supply fresh air; consult doctor in case of complaints.

· After skin contact: Immediately wash with water and soap and rinse thoroughly. Immediately seek for medical advice.

· After eye contact: Rinse opened eye for several minutes under running water. Immediately seek for medical advice.

· After swallowing: Rinse out mouth and then drink plenty of water.

Immediately seek for medical advice.

Fire-fighting measures

Extinguishing media

Suitable extinguishing agents:

- Water haze

- Water spray

- Fire-extinguishing powder

- CO2

- Foam

- Alcohol resistant foam

For safety reasons unsuitable extinguishing agents: Water with full jet

Special hazards arising from the substance or mixture

During heating or in case of fire poisonous gases are produced.

In case of fire, the following can be released:

Carbon monoxide (CO)

Advice for firefighters

- Protective equipment: Wear self-contained respiratory protective device.

Additional information

- Cool endangered receptacles with water spray.

- Collect contaminated fire fighting water separately. It must not enter the sewage system.

Accidental release measures

Personal precautions, protective equipment and emergency procedures

Wear protective clothing.

Ensure adequate ventilation

Particular danger of slipping on leaked/spilled product.

Environmental precautions:

Do not allow to enter sewers/ surface or ground water.

Do not allow to penetrate the ground/soil.

Methods and material for containment and cleaning up:

Absorb with liquid-binding material (sand, diatomite, acid binders, universal binders, sawdust).

Send for recovery or disposal in suitable receptacles.

Handling and storage

Precautions for safe handling

Keep receptacles tightly sealed.

Ensure good ventilation/exhaustion at the workplace.

Prevent formation of dust.

· Information about fire - and explosion protection: Protect against electrostatic charges.

Conditions for safe storage, including any incompatibilities

· Storage:

· Requirements to be met by storerooms and receptacles: Store only in the original receptacle.

· Information about storage in one common storage facility: Not required.

· Further information about storage conditions:

Keep container tightly sealed.

Store in cool, dry conditions in well sealed receptacles.

Protect from heat and direct sunlight.

Store receptacle in a well ventilated area.

Specific end use(s)

See 1.2

No further relevant information available.

Transport information

Shippingopen allclose all
SpecialProvisionsopen allclose all
Shippingopen allclose all
Remarksopen allclose all

Marine transport (UN RTDG/IMDG)

Shippingopen allclose all
Remarksopen allclose all
Shippingopen allclose all
Remarksopen allclose all
SpecialProvisionsopen allclose all

Exposure controls / personal protection

Control parameters

· Ingredients with limit values that require monitoring at the workplace: Not required.

· Additional information: The lists valid during the making were used as basis.

Exposure controls

· Personal protective equipment:

· General protective and hygienic measures:

The usual precautionary measures are to be adhered to when handling chemicals.

Immediately remove all soiled and contaminated clothing

Wash hands before breaks and at the end of work.

Do not eat or drink while working.

· Respiratory protection:

Use suitable respiratory protective device when high concentrations are present.

Filter A/P2

· Protection of hands:

Protective gloves

Check protective gloves prior to each use for their proper condition.

The glove material has to be impermeable and resistant to the product/ the substance/ the preparation.

Selection of the glove material on consideration of the penetration times, rates of diffusion and the degradation

· Material of gloves

EN374

Butyl rubber, BR

Natural rubber, NR

Neoprene gloves

Fluorocarbon rubber (Viton)

Nitrile rubber, NBR

Chloroprene rubber, CR

PVC gloves

The selection of the suitable gloves does not only depend on the material, but also on further marks of quality and

varies from manufacturer to manufacturer.

· Penetration time of glove material

For the mixture of chemicals mentioned below the penetration time has to be at least 120 minutes (Permeation

according to EN 374 Part 3: Level 4).

The exact break trough time has to be found out by the manufacturer of the protective gloves and has to be

observed.

· Eye protection:

EN 166

Tightly sealed goggles

· Body protection: Protective work clothing

Stability and reactivity

Reactivity

Not determined.

No further relevant information available.

Chemical stability Stable

· Thermal decomposition / conditions to be avoided: No decomposition if used according to specifications.

Possibility of hazardous reactions No dangerous reactions known.

Conditions to avoid Extremely high temperatures

Incompatible materials:

Strong alkalis

Strong Acids

Strong oxidizingagents

Hazardous decomposition products:

Danger of forming toxic pyrolysis products.

Aldehyde

Carbon dioxide

Disposal considerations

Waste treatment methods

· Recommendation Smaller quantities can be disposed of with household waste.

· Uncleaned packaging:

· Recommendation: Disposal must be made according to official regulations.