Registration Dossier

Diss Factsheets

Administrative data

First-aid measures

General information

In case of persisting adverse effects, consult a physician. Change contaminated, saturated clothing.

After inhalation

Remove affected person from the immediate area. Ensure supply of fresh air.

After skin contact

Wash off immediately with soap and water.

After eye contact

Separate eyelids, wash the eyes thoroughly with water (15 min.).

After ingestion

Do not induce vomiting. Rinse out mouth and give plenty of water to drink. Never give anything by mouth to an unconscious person.

Fire-fighting measures

5.1       Extinguishing media

Suitable extinguishing media

Alcohol-resistant foam; extinguishing powder; extinguishing powder; Water spray jet

Unsuitable extinguishing media

No data available.

5.2       Special hazards arising from the substance or mixture

In the event of fire, the following can be released: Carbon dioxide (CO2); Carbon monoxide (CO); Acetaldehyde

5.3       Advice for firefighters

Use self-contained breathing apparatus. Wear protective clothing. Cool endangered containers with water spray jet.

Accidental release measures

6.1       Personal precautions, protective equipment and emergency procedures

For non-emergency personnel

Refer to protective measures listed in sections 7 and 8.

For emergency responders

No data available. Personal protective equipment (PPE) - see Section 8.

6.2       Environmental precautions

Do not discharge into the drains/surface waters/groundwater. Do not discharge into the subsoil/soil.

6.3       Methods and material for containment and cleaning up

Take up mechanically. When picked up, treat material as prescribed under heading "Disposal considerations".

Handling and storage

7.1       Precautions for safe handling

Advice on safe handling

Provide good ventilation of working area (local exhaust ventilation, if necessary). Avoid contact with skin and eyes.

General protective and hygiene measures

Do not eat, drink or smoke during work time. Keep away from foodstuffs and beverages. Wash hands before breaks and after work. Provide eye wash fountain in work area. Do not inhale dust.

Advice on protection against fire and explosion

Keep away from sources of heat and ignition. Dust can form an explosive mixture with air.

7.2       Conditions for safe storage, including any incompatibilities

Technical measures and storage conditions

Keep container tightly closed in a cool, well-ventilated place.

Requirements for storage rooms and vessels

Containers which are opened must be carefully resealed and kept upright to prevent leakage.

Advice on storage assembly

Do not store together with: Oxidizing agents; Mineral acids

Transport information

Shippingopen allclose all
SpecialProvisionsopen allclose all
Shippingopen allclose all
Remarksopen allclose all

Marine transport (UN RTDG/IMDG)

Shippingopen allclose all
Remarksopen allclose all

Air transport (UN RTDG/ICAO/IATA)

Shippingopen allclose all
Special provisions / remarks
Transport code: None known
Transport: Avoid crushing the containers. In the event of a spillage,
observe the warning labels on the container
SpecialProvisionsopen allclose all

Exposure controls / personal protection

8.1       Control parameters

No parameters available for monitoring.

8.2       Exposure controls

Appropriate engineering controls

No data available.

Personal protective equipment

Respiratory protection

If workplace exposure limits are exceeded, a respiration protection approved for this particular job must be worn. In case of dust formation, take appropriate measures for breathing protection  in the event workplace threshold values are not specified.

Eye / face protection

Safety glasses (EN 166)

Hand protection

In case of intensive contact, wear protective gloves (EN 374). Sufficient protection is given wearing suitable protective gloves checked according to i.e. EN 374, in the event of risk of skin contact with the product . Before use, the protective gloves should be tested in any case for its specific work-station suitability (i.e. mechanical resistance, product compatibility and antistatic properties). Adhere to the manufacturer’s instructions and information relating to the use, storage, care and replacement of protective gloves. Protective gloves shall be replaced immediately when physically damaged or worn. Design operations thus to avoid permanent use of protective gloves.


Normal chemical work clothing.

Environmental exposure controls

No data available.

Stability and reactivity

Da10.1       Reactivity

No data available.

10.2       Chemical stability

Stable under recommended storage and handling conditions(See section 7).

10.3       Possibility of hazardous reactions

No data available.

10.4       Conditions to avoid

Avoid formation of dust.

10.5       Incompatible materials

Oxidizing agents; Mineral acids

10.6       Hazardous decomposition products


Disposal considerations

13.1       Waste treatment methods


Allocation of a waste code number, according to the European Waste Catalogue, should be carried out in agreement with the regional waste disposal company.


Residuals must be removed from packaging and when emptied completely disposed of in accordance with the regulations for waste removal. Incompletely emptied packaging must be disposed of in the form of disposal specified by the regional disposer.