legislation-obligation
legislation-obligation
Substance Regulatory Obligations
OBL
Sulphur dioxide
EC number: 231-195-2
CAS number: 7446-09-5
Last updated: 03/04/2024
ECHA Legislation Regulatory Obligations
Regulatory obligations may exist for this substance under the legislations under ECHA’s remit or for which ECHA has delegated tasks (i.e. REACH, CLP, BPR, PIC, CAD / CMD, WFD, and POPs). Please check the substance Infocard.
Active Implantable Medical Devices Directive-repealed
Active Implantable Medical Devices Directive - Hazardous Substances
This list contains hazardous substances for purposes of Directive 90/385/EEC on active implantable medical devices, particularly as regards Article 3 and Annex I (Essential Requirements). This non-exhaustive database is derived from: Table 3 of Annex VI to CLP, REACH Candidate List of SVHCs, and Directive 2000/54/EC's Annex III (Biological Agents list). Please note that Regulation (EU) 2017/745 on medical devices has repealed Directive 90/385/EEC and begun to apply from 26 May 2021. Nevertheless, Article 120 of the Regulation provides for a transitional period allowing medical devices, under specified conditions (e.g., placed on the market prior to 26 May 2021), to continue to comply with the Directive. In accordance with the fourth paragraph of Article 120, this period ends 26 May 2025.
| Name | CAS | EU CLP (1272/2008) | EU_BA Directive 2000/54/EC | EU REACH: List of SVHC |
|---|---|---|---|---|
|
sulphur dioxide |
7446-09-5 |
Press. Gas; Acute Tox. 3; Skin Corr. 1B |
||
Ambient Air Quality Directive
Annexes II VII XI XII XIII XIV - Assessment Thresholds & Limit Values
This list contains the Limit, Critical, Target and Long-term Values on ambient air for protection of human health and vegetation. It also contains the Alert, Information and Upper and Lower Assessment thresholds for sulphur dioxide, nitrogen dioxide, benzene, carbon monoxide, lead, PM2.5, PM10 and ozone.
| Name | CAS | Critical Level | Alert Threshold | Upper assessment threshold | Lower assessment threshold | Average limit | Average sampling duration | Tolerance margin | Exposure conc. Obligation | Information Threshold | Long-term objective | Objective | Target value | Annex | Qualifier | Notes | |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
|
Sulphur dioxide |
7446-09-5 |
500 µg/m3 |
350 µg/m3 |
1 h |
43 % |
Protection of Human Health |
XI (Section B),XII (Section A) |
01 Without prejudice to Annex I, the criteria for 'Required proportion of valid data' shall be used for checking validity when aggregating data and calculating statistical parameters 02 Limit value not to be exceeded more than 24 times a calendar year 07 Already in force since 1 January 2005 29 Alert thresholds: To be measured over three consecutive hours at locations representative of air quality over at least 100 km2 or an entire zone or agglomeration, whichever is the smaller 30 Average Limit is the Limit Value, a level fixed with the aim of avoiding, preventing or reducing harmful effects on human health and/or the environment and not to be exceeded once attained |
Details | ||||||||
|
Sulphur dioxide |
7446-09-5 |
75 µg/m3 |
50 µg/m3 |
125 µg/m3 |
1 d |
0 % |
Protection of Human Health |
XI (Section B),II (Section A1) |
01 Without prejudice to Annex I, the criteria for 'Required proportion of valid data' shall be used for checking validity when aggregating data and calculating statistical parameters 03 Limit value not to be exceeded more than 3 times a calendar year. Applies to Upper and lower thresholds. 07 Already in force since 1 January 2005 14 The required proportion of valid data for the Limit Value referes to the percentage of the hourly averages 30 Average Limit is the Limit Value, a level fixed with the aim of avoiding, preventing or reducing harmful effects on human health and/or the environment and not to be exceeded once attained |
Details | |||||||
|
Sulphur dioxide |
7446-09-5 |
20 µg/m3 |
12 µg/m3 |
8 µg/m3 |
15 Months |
0 % |
Protection of vegetation |
XIII,II (Section A1) |
23 The averaging period referes to Calendar year and winter (1 October to 31 March) 27 The upper and lower assessment thresholds correspond to 60% and 40% respectively of winter critical level |
Details | |||||||
CAD - Chemical Agents Directive
CAD - Chemical Agents Directive, Article 2(b)(i) - Hazardous Agents
This list contains a non-exhaustive inventory based on the list of substances with harmonised classification and labelling (i.e., Table 3 of Annex VI to the CLP Regulation 1272/2008/EC). While the harmonised list covers many hazardous substances, others not listed may also meet the classification criteria in accordance with the CLP Regulation.
| Name | CAS |
|---|---|
|
sulphur dioxide |
7446-09-5 |
Construction Products Regulation
Construction Product Regulation - Annex I (3) - Hazardous Substances
This list contains a non-exhaustive inventory of substances taken from: (1) Table 3 of Annex VI to CLP; (2) the Candidate List of SVHCs; (3) Annex XIV of REACH (Authorisation List); (4) Annex XVII of REACH (Restrictions List); (5) F-gases subject to emission limits/reporting per Regulation 517/2014/EU; and (6) volatile organic compounds (VOCs) listed in the Ambient Air Directive 2008/50/EC. The basis of the list is Annex I(3) of the Construction Products Regulation 305/2011/EC, which stipulates that construction works must not have a high impact on human health or the environment as a result of: giving off toxic gas; emissions of dangerous substances, volatile organic compounds (VOC), greenhouse gases or dangerous particles into indoor or outdoor air; release of dangerous substances into drinking water, ground water, marine waters, surface waters or soil.
| Name | CAS | EU CLP (1272/2008) | EU REACH: Annex XIV | EU REACH: List of SVHC | EU REACH: Annex XVII | EU FGG (517/2014) | EU VOC (2008/50) |
|---|---|---|---|---|---|---|---|
|
sulphur dioxide |
7446-09-5 |
yes |
|||||
Construction Product Regulation - Article 6(5) - SDS and Declaration
This list contains a non-exhaustive inventory of substances originating from: (1) Table 3 of Annex VI to CLP (i.e., the list of harmonised substances); (2) the Candidate List of Substances of Very High Concern (SVHCs); and REACH Annex XIV (Authorisation List). This list is compiled on the basis of Article 6(5) of Regulation 305/2011/EC on Marketing of Construction Products. This provision requires SDSs and information on hazardous substances (i.e., SVHCs) contained in construction products be provided with the declaration of performance.
| Name | CAS | EU REACH: Annex XIV | EU REACH: List of SVHC |
|---|---|---|---|
|
sulphur dioxide |
7446-09-5 |
||
End-of-Life Vehicles Directive
End-of-Life Vehicles Directive - Hazardous Substances
This list contains a non-exhaustive inventory of hazardous substances as defined by Article 2(11) of the End-of-Life Vehicles Directive 2000/53/EC. It is based on the relevant subset of substances with harmonised classification listed in Table 3 of Annex VI to the CLP Regulation 1272/2008/EC.
| Name | CAS | EU CLP (1272/2008) |
|---|---|---|
|
sulphur dioxide |
7446-09-5 |
Acute Tox. 3; STOT SE 1 |
EU Ecolabel Regulation
Ecolabel - Restrictions for Hazardous Substances/Mixtures
This list contains a non-exhaustive inventory of substances based on the list of hazardous substances with harmonised classification and labelling (i.e. Table 3 of Annex VI to the CLP Regulation), and the Candidate List of substances of very high concern (SVHCs). Pursuant to Article 6(6) of the EU Ecolabel Regulation, the ecolabel must not be awarded to goods containing substances or mixtures classified according to the CLP as toxic; hazardous to the environment; and carcinogenic, mutagenic, or toxic for reproduction (CMRs). Nor are products allowed the ecolabel award when they contain SVHCs (per Article 57 of REACH). While the CLP's harmonised list contains many such substances, other ones not listed in Table 3 may also meet the criteria specified for classification under the CLP.
| Name | CAS | Restriction(s) | Expressed As | Table 3 of Annex VI to CLP | EU REACH: List of SVHC | Physical form | Substance Description | |
|---|---|---|---|---|---|---|---|---|
|
sulphur dioxide |
7446-09-5 |
yes |
Details | |||||
General Product Safety Directive
General Product Safety Directive - Hazardous Substances
This list contains a non-exhaustive inventory of substances that fall within the European Union's hazardous substance definitions, as provided on: (1) Table 3 of Annex VI to the CLP Regulation 1272/2008/EC; (2) Annex III of Directive 2000/54/EC (Biological Agents); Candidate List of SVHCs; and REACH Annexes XIV and XVII (Authorisation and Restriction lists). They can be considered hazardous for purposes of the General Product Safety Directive 2001/95/EC.
| Name | CAS | EU CLP (1272/2008) | EU REACH: Annex XIV | EU REACH: List of SVHC | EU REACH: Annex XVII | EU_BA Directive 2000/54/EC |
|---|---|---|---|---|---|---|
|
sulphur dioxide |
7446-09-5 |
yes |
||||
In Vitro Diagnostic Medical Devices Directive-repealed
In Vitro Diagnostic Medical Devices Directive - Hazardous Substances
This list contains a non-exhaustive inventory of hazardous substances for purposes of essential requirements (Article 3 and Annex I) for general safety, design, manufacture and hazard communication of in vitro diagnostic medical devices. It is derived from: Table 3 of Annex VI to CLP, REACH Candidate List of SVHCs, and Directive 2000/54/EC's Annex III (Biological Agents list). Note that Regulation 2017/746/EU on in vitro diagnostic medical devices was published in the EU Official Journal on 5 May 2017. With few exceptions specified in Articles 112 and 113 of this Regulation, Directive 98/79/EC is repealed, and the rules pursuant to 2017/746/EU apply, from 26 May 2022.
| Name | CAS | EU CLP (1272/2008) | EU_BA Directive 2000/54/EC | EU REACH: List of SVHC |
|---|---|---|---|---|
|
sulphur dioxide |
7446-09-5 |
Press. Gas; Acute Tox. 3; Skin Corr. 1B |
||
In Vitro Diagnostic Medical Devices Regulation
In Vitro Diagnostic Medical Devices Regulation - Hazardous Substances
This list contains a non-exhaustive inventory of hazardous substances for purposes of Regulation (EU) 2017/746, including Chap. 2 (Placing on the market and putting into service) and Annex I (General Safety and Performance Requirements). It is derived from: Table 3 of Annex VI to CLP, REACH Candidate List of SVHCs, and Directive 2000/54/EC's Annex III (Biological Agents list).
| EU CLP (1272/2008) | EU_BA Directive 2000/54/EC | EU REACH: List of SVHC | |
|---|---|---|---|
|
Press. Gas; Acute Tox. 3; STOT SE 1; Skin Corr. 1B |
Details | ||
Industrial Emissions Directive
IPPC - Industrial Emissions Directive, Annex II - Polluting Substances
This list contains the polluting substances for which emission limit values are assigned under Directive 2010/75/EU on Industrial Emissions (Integrated Pollution Prevention and Control - IPPC). Member States must permit all qualifying facilities in order to ensure that they minimize impact on the environment. The permit issued must provide emission limit values for pollutants on this list.
| Name | CAS | Air | Water | Annex X of Dir 2000/60/EC |
|---|---|---|---|---|
|
Sulphur dioxide |
7446-09-5 |
yes |
||
IPPC, Annexes V, VI, VIII - Provisions relating to industrial plants
This list contains emission limit values for polluting substances in waste gases and waste water, assigned according to facility type (i.e., combustion plants (Annex V), waste incineration/co-incineration plants (Annex VI), and installations producing titanium dioxide (Annex VIII)), under Directive 2010/75/EU on Industrial Emissions (Integrated Pollution Prevention and Control - IPPC). For this list, if a substance presents 2 values in the ''Average sampling duration'' field, these indicate minimum and maximum average sampling period.
| Name | CAS | Expressed As | Annex | Group | Average duration qualifier | Average limit | Maximum limit | Average sampling duration | Emission medium | fuel | Fuel class | Part | Point | Thermal input | Process/equipment | Qualifier | Notes | |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
|
Sulphur dioxide SO2 |
7446-09-5 |
V Annex V (Directive 2010/75/EU) Technical provisions relating to combustion plants |
400 mg/Nm3 |
Waste gases |
Coal and lignite and other solid fuels |
Solid |
Part 1 (V) Emission limit values for combustion plants referred to in Article 30(2) |
2 |
50-100 |
Combustion plants using solid or liquid fuels with the exception of gas turbines and gas engines |
00 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correction for the water vapour content of the waste gases and at a standardised O2 content of 6 % for solid fuels, 3 % for combustion plants, other than gas turbines and gas engines using liquid and gaseous fuels and 15 % for gas turbines and gas engines 09 Combustion plants, using solid fuels which were granted a permit before 27 November 2002 or the operators of which had submitted a complete application for a permit before that date, provided that the plant was put into operation no later than 27 November 2003, and which do not operate more than 1500 operating hours per year as a rolling average over a period of 5 years, shall be subject to an emission limit value for SO2 of 800 mg/Nm3 37 For technical provisions regarding 'Emission monitoring' see Part 3 (Annex V). For 'Assessment of compliance with emission limit values' see Part 4 (Annex V) Directive 2010/75/EU 38 For technical provisions regarding 'Minimum rate of desulphurisation' see Part 5 (Annex V). For 'Compliance with rate of desulphurisation' see Part 6 (Annex V) Directive 2010/75/EU |
Details | ||||||
|
Sulphur dioxide SO2 |
7446-09-5 |
V Annex V (Directive 2010/75/EU) Technical provisions relating to combustion plants |
250 mg/Nm3 |
Waste gases |
Coal and lignite and other solid fuels |
Solid |
Part 1 (V) Emission limit values for combustion plants referred to in Article 30(2) |
2 |
100-300 |
Combustion plants using solid or liquid fuels with the exception of gas turbines and gas engines |
00 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correction for the water vapour content of the waste gases and at a standardised O2 content of 6 % for solid fuels, 3 % for combustion plants, other than gas turbines and gas engines using liquid and gaseous fuels and 15 % for gas turbines and gas engines 09 Combustion plants, using solid fuels which were granted a permit before 27 November 2002 or the operators of which had submitted a complete application for a permit before that date, provided that the plant was put into operation no later than 27 November 2003, and which do not operate more than 1500 operating hours per year as a rolling average over a period of 5 years, shall be subject to an emission limit value for SO2 of 800 mg/Nm3 37 For technical provisions regarding 'Emission monitoring' see Part 3 (Annex V). For 'Assessment of compliance with emission limit values' see Part 4 (Annex V) Directive 2010/75/EU 38 For technical provisions regarding 'Minimum rate of desulphurisation' see Part 5 (Annex V). For 'Compliance with rate of desulphurisation' see Part 6 (Annex V) Directive 2010/75/EU |
Details | ||||||
|
Sulphur dioxide SO2 |
7446-09-5 |
V Annex V (Directive 2010/75/EU) Technical provisions relating to combustion plants |
200 mg/Nm3 |
Waste gases |
Coal and lignite and other solid fuels |
Solid |
Part 1 (V) Emission limit values for combustion plants referred to in Article 30(2) |
2 |
> 300 |
Combustion plants using solid or liquid fuels with the exception of gas turbines and gas engines |
00 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correction for the water vapour content of the waste gases and at a standardised O2 content of 6 % for solid fuels, 3 % for combustion plants, other than gas turbines and gas engines using liquid and gaseous fuels and 15 % for gas turbines and gas engines 09 Combustion plants, using solid fuels which were granted a permit before 27 November 2002 or the operators of which had submitted a complete application for a permit before that date, provided that the plant was put into operation no later than 27 November 2003, and which do not operate more than 1500 operating hours per year as a rolling average over a period of 5 years, shall be subject to an emission limit value for SO2 of 800 mg/Nm3 37 For technical provisions regarding 'Emission monitoring' see Part 3 (Annex V). For 'Assessment of compliance with emission limit values' see Part 4 (Annex V) Directive 2010/75/EU 38 For technical provisions regarding 'Minimum rate of desulphurisation' see Part 5 (Annex V). For 'Compliance with rate of desulphurisation' see Part 6 (Annex V) Directive 2010/75/EU |
Details | ||||||
|
Sulphur dioxide SO2 |
7446-09-5 |
V Annex V (Directive 2010/75/EU) Technical provisions relating to combustion plants |
200 mg/Nm3 |
Waste gases |
Biomass |
Solid |
Part 1 (V) Emission limit values for combustion plants referred to in Article 30(2) |
2 |
50-100 |
Combustion plants using solid or liquid fuels with the exception of gas turbines and gas engines |
00 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correction for the water vapour content of the waste gases and at a standardised O2 content of 6 % for solid fuels, 3 % for combustion plants, other than gas turbines and gas engines using liquid and gaseous fuels and 15 % for gas turbines and gas engines 09 Combustion plants, using solid fuels which were granted a permit before 27 November 2002 or the operators of which had submitted a complete application for a permit before that date, provided that the plant was put into operation no later than 27 November 2003, and which do not operate more than 1500 operating hours per year as a rolling average over a period of 5 years, shall be subject to an emission limit value for SO2 of 800 mg/Nm3 37 For technical provisions regarding 'Emission monitoring' see Part 3 (Annex V). For 'Assessment of compliance with emission limit values' see Part 4 (Annex V) Directive 2010/75/EU 38 For technical provisions regarding 'Minimum rate of desulphurisation' see Part 5 (Annex V). For 'Compliance with rate of desulphurisation' see Part 6 (Annex V) Directive 2010/75/EU |
Details | ||||||
|
Sulphur dioxide SO2 |
7446-09-5 |
V Annex V (Directive 2010/75/EU) Technical provisions relating to combustion plants |
200 mg/Nm3 |
Waste gases |
Biomass |
Solid |
Part 1 (V) Emission limit values for combustion plants referred to in Article 30(2) |
2 |
100-300 |
Combustion plants using solid or liquid fuels with the exception of gas turbines and gas engines |
00 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correction for the water vapour content of the waste gases and at a standardised O2 content of 6 % for solid fuels, 3 % for combustion plants, other than gas turbines and gas engines using liquid and gaseous fuels and 15 % for gas turbines and gas engines 09 Combustion plants, using solid fuels which were granted a permit before 27 November 2002 or the operators of which had submitted a complete application for a permit before that date, provided that the plant was put into operation no later than 27 November 2003, and which do not operate more than 1500 operating hours per year as a rolling average over a period of 5 years, shall be subject to an emission limit value for SO2 of 800 mg/Nm3 37 For technical provisions regarding 'Emission monitoring' see Part 3 (Annex V). For 'Assessment of compliance with emission limit values' see Part 4 (Annex V) Directive 2010/75/EU 38 For technical provisions regarding 'Minimum rate of desulphurisation' see Part 5 (Annex V). For 'Compliance with rate of desulphurisation' see Part 6 (Annex V) Directive 2010/75/EU |
Details | ||||||
|
Sulphur dioxide SO2 |
7446-09-5 |
V Annex V (Directive 2010/75/EU) Technical provisions relating to combustion plants |
200 mg/Nm3 |
Waste gases |
Biomass |
Solid |
Part 1 (V) Emission limit values for combustion plants referred to in Article 30(2) |
2 |
> 300 |
Combustion plants using solid or liquid fuels with the exception of gas turbines and gas engines |
00 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correction for the water vapour content of the waste gases and at a standardised O2 content of 6 % for solid fuels, 3 % for combustion plants, other than gas turbines and gas engines using liquid and gaseous fuels and 15 % for gas turbines and gas engines 09 Combustion plants, using solid fuels which were granted a permit before 27 November 2002 or the operators of which had submitted a complete application for a permit before that date, provided that the plant was put into operation no later than 27 November 2003, and which do not operate more than 1500 operating hours per year as a rolling average over a period of 5 years, shall be subject to an emission limit value for SO2 of 800 mg/Nm3 37 For technical provisions regarding 'Emission monitoring' see Part 3 (Annex V). For 'Assessment of compliance with emission limit values' see Part 4 (Annex V) Directive 2010/75/EU 38 For technical provisions regarding 'Minimum rate of desulphurisation' see Part 5 (Annex V). For 'Compliance with rate of desulphurisation' see Part 6 (Annex V) Directive 2010/75/EU |
Details | ||||||
|
Sulphur dioxide SO2 |
7446-09-5 |
V Annex V (Directive 2010/75/EU) Technical provisions relating to combustion plants |
300 mg/Nm3 |
Waste gases |
Peat |
Solid |
Part 1 (V) Emission limit values for combustion plants referred to in Article 30(2) |
2 |
50-100 |
Combustion plants using solid or liquid fuels with the exception of gas turbines and gas engines |
00 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correction for the water vapour content of the waste gases and at a standardised O2 content of 6 % for solid fuels, 3 % for combustion plants, other than gas turbines and gas engines using liquid and gaseous fuels and 15 % for gas turbines and gas engines 09 Combustion plants, using solid fuels which were granted a permit before 27 November 2002 or the operators of which had submitted a complete application for a permit before that date, provided that the plant was put into operation no later than 27 November 2003, and which do not operate more than 1500 operating hours per year as a rolling average over a period of 5 years, shall be subject to an emission limit value for SO2 of 800 mg/Nm3 37 For technical provisions regarding 'Emission monitoring' see Part 3 (Annex V). For 'Assessment of compliance with emission limit values' see Part 4 (Annex V) Directive 2010/75/EU 38 For technical provisions regarding 'Minimum rate of desulphurisation' see Part 5 (Annex V). For 'Compliance with rate of desulphurisation' see Part 6 (Annex V) Directive 2010/75/EU |
Details | ||||||
|
Sulphur dioxide SO2 |
7446-09-5 |
V Annex V (Directive 2010/75/EU) Technical provisions relating to combustion plants |
300 mg/Nm3 |
Waste gases |
Peat |
Solid |
Part 1 (V) Emission limit values for combustion plants referred to in Article 30(2) |
2 |
100-300 |
Combustion plants using solid or liquid fuels with the exception of gas turbines and gas engines |
00 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correction for the water vapour content of the waste gases and at a standardised O2 content of 6 % for solid fuels, 3 % for combustion plants, other than gas turbines and gas engines using liquid and gaseous fuels and 15 % for gas turbines and gas engines 09 Combustion plants, using solid fuels which were granted a permit before 27 November 2002 or the operators of which had submitted a complete application for a permit before that date, provided that the plant was put into operation no later than 27 November 2003, and which do not operate more than 1500 operating hours per year as a rolling average over a period of 5 years, shall be subject to an emission limit value for SO2 of 800 mg/Nm3 37 For technical provisions regarding 'Emission monitoring' see Part 3 (Annex V). For 'Assessment of compliance with emission limit values' see Part 4 (Annex V) Directive 2010/75/EU 38 For technical provisions regarding 'Minimum rate of desulphurisation' see Part 5 (Annex V). For 'Compliance with rate of desulphurisation' see Part 6 (Annex V) Directive 2010/75/EU |
Details | ||||||
|
Sulphur dioxide SO2 |
7446-09-5 |
V Annex V (Directive 2010/75/EU) Technical provisions relating to combustion plants |
200 mg/Nm3 |
Waste gases |
Peat |
Solid |
Part 1 (V) Emission limit values for combustion plants referred to in Article 30(2) |
2 |
> 300 |
Combustion plants using solid or liquid fuels with the exception of gas turbines and gas engines |
00 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correction for the water vapour content of the waste gases and at a standardised O2 content of 6 % for solid fuels, 3 % for combustion plants, other than gas turbines and gas engines using liquid and gaseous fuels and 15 % for gas turbines and gas engines 09 Combustion plants, using solid fuels which were granted a permit before 27 November 2002 or the operators of which had submitted a complete application for a permit before that date, provided that the plant was put into operation no later than 27 November 2003, and which do not operate more than 1500 operating hours per year as a rolling average over a period of 5 years, shall be subject to an emission limit value for SO2 of 800 mg/Nm3 37 For technical provisions regarding 'Emission monitoring' see Part 3 (Annex V). For 'Assessment of compliance with emission limit values' see Part 4 (Annex V) Directive 2010/75/EU 38 For technical provisions regarding 'Minimum rate of desulphurisation' see Part 5 (Annex V). For 'Compliance with rate of desulphurisation' see Part 6 (Annex V) Directive 2010/75/EU |
Details | ||||||
|
Sulphur dioxide SO2 |
7446-09-5 |
V Annex V (Directive 2010/75/EU) Technical provisions relating to combustion plants |
350 mg/Nm3 |
Waste gases |
Liquid |
Part 1 (V) Emission limit values for combustion plants referred to in Article 30(2) |
2 |
50-100 |
Combustion plants using solid or liquid fuels with the exception of gas turbines and gas engines |
00 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correction for the water vapour content of the waste gases and at a standardised O2 content of 6 % for solid fuels, 3 % for combustion plants, other than gas turbines and gas engines using liquid and gaseous fuels and 15 % for gas turbines and gas engines 10 Combustion plants using liquid fuels with a granted permit before 27 Nov 2002 or a submitted complete application for permit before that date, provided that the plant was put into operation before 27 Nov 2003, and with no more than 1500 operating h/year as a rolling average over a period of 5 years, shall be subject to an emission limit for SO2 of 850 mg/Nm3 in case of plants with a total rated thermal input (TRTI) below 300 MW and of 400 mg/Nm3 in case of plants with a TRTI greater than 300 MW 37 For technical provisions regarding 'Emission monitoring' see Part 3 (Annex V). For 'Assessment of compliance with emission limit values' see Part 4 (Annex V) Directive 2010/75/EU 38 For technical provisions regarding 'Minimum rate of desulphurisation' see Part 5 (Annex V). For 'Compliance with rate of desulphurisation' see Part 6 (Annex V) Directive 2010/75/EU |
Details | |||||||
|
Sulphur dioxide SO2 |
7446-09-5 |
V Annex V (Directive 2010/75/EU) Technical provisions relating to combustion plants |
250 mg/Nm3 |
Waste gases |
Liquid |
Part 1 (V) Emission limit values for combustion plants referred to in Article 30(2) |
2 |
100-300 |
Combustion plants using solid or liquid fuels with the exception of gas turbines and gas engines |
00 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correction for the water vapour content of the waste gases and at a standardised O2 content of 6 % for solid fuels, 3 % for combustion plants, other than gas turbines and gas engines using liquid and gaseous fuels and 15 % for gas turbines and gas engines 10 Combustion plants using liquid fuels with a granted permit before 27 Nov 2002 or a submitted complete application for permit before that date, provided that the plant was put into operation before 27 Nov 2003, and with no more than 1500 operating h/year as a rolling average over a period of 5 years, shall be subject to an emission limit for SO2 of 850 mg/Nm3 in case of plants with a total rated thermal input (TRTI) below 300 MW and of 400 mg/Nm3 in case of plants with a TRTI greater than 300 MW 37 For technical provisions regarding 'Emission monitoring' see Part 3 (Annex V). For 'Assessment of compliance with emission limit values' see Part 4 (Annex V) Directive 2010/75/EU 38 For technical provisions regarding 'Minimum rate of desulphurisation' see Part 5 (Annex V). For 'Compliance with rate of desulphurisation' see Part 6 (Annex V) Directive 2010/75/EU |
Details | |||||||
|
Sulphur dioxide SO2 |
7446-09-5 |
V Annex V (Directive 2010/75/EU) Technical provisions relating to combustion plants |
200 mg/Nm3 |
Waste gases |
Liquid |
Part 1 (V) Emission limit values for combustion plants referred to in Article 30(2) |
2 |
> 300 |
Combustion plants using solid or liquid fuels with the exception of gas turbines and gas engines |
00 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correction for the water vapour content of the waste gases and at a standardised O2 content of 6 % for solid fuels, 3 % for combustion plants, other than gas turbines and gas engines using liquid and gaseous fuels and 15 % for gas turbines and gas engines 10 Combustion plants using liquid fuels with a granted permit before 27 Nov 2002 or a submitted complete application for permit before that date, provided that the plant was put into operation before 27 Nov 2003, and with no more than 1500 operating h/year as a rolling average over a period of 5 years, shall be subject to an emission limit for SO2 of 850 mg/Nm3 in case of plants with a total rated thermal input (TRTI) below 300 MW and of 400 mg/Nm3 in case of plants with a TRTI greater than 300 MW 37 For technical provisions regarding 'Emission monitoring' see Part 3 (Annex V). For 'Assessment of compliance with emission limit values' see Part 4 (Annex V) Directive 2010/75/EU 38 For technical provisions regarding 'Minimum rate of desulphurisation' see Part 5 (Annex V). For 'Compliance with rate of desulphurisation' see Part 6 (Annex V) Directive 2010/75/EU |
Details | |||||||
|
Sulphur dioxide SO2 |
7446-09-5 |
V Annex V (Directive 2010/75/EU) Technical provisions relating to combustion plants |
35 mg/Nm3 |
Waste gases |
In general |
Gas |
Part 1 (V) Emission limit values for combustion plants referred to in Article 30(2) |
3 |
Combustion plants using gaseous fuels with the exception of gas turbines and gas engines |
00 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correction for the water vapour content of the waste gases and at a standardised O2 content of 6 % for solid fuels, 3 % for combustion plants, other than gas turbines and gas engines using liquid and gaseous fuels and 15 % for gas turbines and gas engines 11 Combustion plants, firing low calorific gases from gasification of refinery residues, which were granted a permit before 27 November 2002 or the operators of which had submitted a complete application for a permit before that date, provided that the plant was put into operation no later than 27 November 2003, shall be subject to an emission limit value for SO2 of 800 mg/Nm3 37 For technical provisions regarding 'Emission monitoring' see Part 3 (Annex V). For 'Assessment of compliance with emission limit values' see Part 4 (Annex V) Directive 2010/75/EU 38 For technical provisions regarding 'Minimum rate of desulphurisation' see Part 5 (Annex V). For 'Compliance with rate of desulphurisation' see Part 6 (Annex V) Directive 2010/75/EU |
Details | |||||||
|
Sulphur dioxide SO2 |
7446-09-5 |
V Annex V (Directive 2010/75/EU) Technical provisions relating to combustion plants |
5 mg/Nm3 |
Waste gases |
Liquified gas |
Gas |
Part 1 (V) Emission limit values for combustion plants referred to in Article 30(2) |
3 |
Combustion plants using gaseous fuels with the exception of gas turbines and gas engines |
00 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correction for the water vapour content of the waste gases and at a standardised O2 content of 6 % for solid fuels, 3 % for combustion plants, other than gas turbines and gas engines using liquid and gaseous fuels and 15 % for gas turbines and gas engines 11 Combustion plants, firing low calorific gases from gasification of refinery residues, which were granted a permit before 27 November 2002 or the operators of which had submitted a complete application for a permit before that date, provided that the plant was put into operation no later than 27 November 2003, shall be subject to an emission limit value for SO2 of 800 mg/Nm3 37 For technical provisions regarding 'Emission monitoring' see Part 3 (Annex V). For 'Assessment of compliance with emission limit values' see Part 4 (Annex V) Directive 2010/75/EU 38 For technical provisions regarding 'Minimum rate of desulphurisation' see Part 5 (Annex V). For 'Compliance with rate of desulphurisation' see Part 6 (Annex V) Directive 2010/75/EU |
Details | |||||||
|
Sulphur dioxide SO2 |
7446-09-5 |
V Annex V (Directive 2010/75/EU) Technical provisions relating to combustion plants |
400 mg/Nm3 |
Waste gases |
Low calorific gases from coke oven |
Gas |
Part 1 (V) Emission limit values for combustion plants referred to in Article 30(2) |
3 |
Combustion plants using gaseous fuels with the exception of gas turbines and gas engines |
00 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correction for the water vapour content of the waste gases and at a standardised O2 content of 6 % for solid fuels, 3 % for combustion plants, other than gas turbines and gas engines using liquid and gaseous fuels and 15 % for gas turbines and gas engines 11 Combustion plants, firing low calorific gases from gasification of refinery residues, which were granted a permit before 27 November 2002 or the operators of which had submitted a complete application for a permit before that date, provided that the plant was put into operation no later than 27 November 2003, shall be subject to an emission limit value for SO2 of 800 mg/Nm3 37 For technical provisions regarding 'Emission monitoring' see Part 3 (Annex V). For 'Assessment of compliance with emission limit values' see Part 4 (Annex V) Directive 2010/75/EU 38 For technical provisions regarding 'Minimum rate of desulphurisation' see Part 5 (Annex V). For 'Compliance with rate of desulphurisation' see Part 6 (Annex V) Directive 2010/75/EU |
Details | |||||||
|
Sulphur dioxide SO2 |
7446-09-5 |
V Annex V (Directive 2010/75/EU) Technical provisions relating to combustion plants |
200 mg/Nm3 |
Waste gases |
Low calorific gases from blast furnace |
Gas |
Part 1 (V) Emission limit values for combustion plants referred to in Article 30(2) |
3 |
Combustion plants using gaseous fuels with the exception of gas turbines and gas engines |
00 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correction for the water vapour content of the waste gases and at a standardised O2 content of 6 % for solid fuels, 3 % for combustion plants, other than gas turbines and gas engines using liquid and gaseous fuels and 15 % for gas turbines and gas engines 11 Combustion plants, firing low calorific gases from gasification of refinery residues, which were granted a permit before 27 November 2002 or the operators of which had submitted a complete application for a permit before that date, provided that the plant was put into operation no later than 27 November 2003, shall be subject to an emission limit value for SO2 of 800 mg/Nm3 37 For technical provisions regarding 'Emission monitoring' see Part 3 (Annex V). For 'Assessment of compliance with emission limit values' see Part 4 (Annex V) Directive 2010/75/EU 38 For technical provisions regarding 'Minimum rate of desulphurisation' see Part 5 (Annex V). For 'Compliance with rate of desulphurisation' see Part 6 (Annex V) Directive 2010/75/EU |
Details | |||||||
|
Sulphur dioxide SO2 |
7446-09-5 |
V Annex V (Directive 2010/75/EU) Technical provisions relating to combustion plants |
400 mg/Nm3 |
Waste gases |
Coal and lignite and other solid fuels |
Solid |
Part 2 (V) Emission limit values for combustion plants referred to in Article 30(3) |
2 |
50-100 |
Combustion plants using solid or liquid fuels with the exception of gas turbines and gas engines |
00 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correction for the water vapour content of the waste gases and at a standardised O2 content of 6 % for solid fuels, 3 % for combustion plants, other than gas turbines and gas engines using liquid and gaseous fuels and 15 % for gas turbines and gas engines 37 For technical provisions regarding 'Emission monitoring' see Part 3 (Annex V). For 'Assessment of compliance with emission limit values' see Part 4 (Annex V) Directive 2010/75/EU 38 For technical provisions regarding 'Minimum rate of desulphurisation' see Part 5 (Annex V). For 'Compliance with rate of desulphurisation' see Part 6 (Annex V) Directive 2010/75/EU |
Details | ||||||
|
Sulphur dioxide SO2 |
7446-09-5 |
V Annex V (Directive 2010/75/EU) Technical provisions relating to combustion plants |
200 mg/Nm3 |
Waste gases |
Coal and lignite and other solid fuels |
Solid |
Part 2 (V) Emission limit values for combustion plants referred to in Article 30(3) |
2 |
100-300 |
Combustion plants using solid or liquid fuels with the exception of gas turbines and gas engines |
00 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correction for the water vapour content of the waste gases and at a standardised O2 content of 6 % for solid fuels, 3 % for combustion plants, other than gas turbines and gas engines using liquid and gaseous fuels and 15 % for gas turbines and gas engines 37 For technical provisions regarding 'Emission monitoring' see Part 3 (Annex V). For 'Assessment of compliance with emission limit values' see Part 4 (Annex V) Directive 2010/75/EU 38 For technical provisions regarding 'Minimum rate of desulphurisation' see Part 5 (Annex V). For 'Compliance with rate of desulphurisation' see Part 6 (Annex V) Directive 2010/75/EU |
Details | ||||||
|
Sulphur dioxide SO2 |
7446-09-5 |
V Annex V (Directive 2010/75/EU) Technical provisions relating to combustion plants |
150 mg/Nm3 |
Waste gases |
Coal and lignite and other solid fuels |
Solid |
Part 2 (V) Emission limit values for combustion plants referred to in Article 30(3) |
2 |
> 300 |
Combustion plants using solid or liquid fuels with the exception of gas turbines and gas engines |
00 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correction for the water vapour content of the waste gases and at a standardised O2 content of 6 % for solid fuels, 3 % for combustion plants, other than gas turbines and gas engines using liquid and gaseous fuels and 15 % for gas turbines and gas engines 37 For technical provisions regarding 'Emission monitoring' see Part 3 (Annex V). For 'Assessment of compliance with emission limit values' see Part 4 (Annex V) Directive 2010/75/EU 38 For technical provisions regarding 'Minimum rate of desulphurisation' see Part 5 (Annex V). For 'Compliance with rate of desulphurisation' see Part 6 (Annex V) Directive 2010/75/EU |
Details | ||||||
|
Sulphur dioxide SO2 |
7446-09-5 |
V Annex V (Directive 2010/75/EU) Technical provisions relating to combustion plants |
200 mg/Nm3 |
Waste gases |
Coal and lignite and other solid fuels |
Solid |
Part 2 (V) Emission limit values for combustion plants referred to in Article 30(3) |
2 |
> 300 |
Combustion plants using solid or liquid fuels with the exception of gas turbines and gas engines |
In case of circulating or pressurised fluidised bed combustion |
00 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correction for the water vapour content of the waste gases and at a standardised O2 content of 6 % for solid fuels, 3 % for combustion plants, other than gas turbines and gas engines using liquid and gaseous fuels and 15 % for gas turbines and gas engines 37 For technical provisions regarding 'Emission monitoring' see Part 3 (Annex V). For 'Assessment of compliance with emission limit values' see Part 4 (Annex V) Directive 2010/75/EU 38 For technical provisions regarding 'Minimum rate of desulphurisation' see Part 5 (Annex V). For 'Compliance with rate of desulphurisation' see Part 6 (Annex V) Directive 2010/75/EU |
Details | |||||
|
Sulphur dioxide SO2 |
7446-09-5 |
V Annex V (Directive 2010/75/EU) Technical provisions relating to combustion plants |
200 mg/Nm3 |
Waste gases |
Biomass |
Solid |
Part 2 (V) Emission limit values for combustion plants referred to in Article 30(3) |
2 |
50-100 |
Combustion plants using solid or liquid fuels with the exception of gas turbines and gas engines |
00 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correction for the water vapour content of the waste gases and at a standardised O2 content of 6 % for solid fuels, 3 % for combustion plants, other than gas turbines and gas engines using liquid and gaseous fuels and 15 % for gas turbines and gas engines 37 For technical provisions regarding 'Emission monitoring' see Part 3 (Annex V). For 'Assessment of compliance with emission limit values' see Part 4 (Annex V) Directive 2010/75/EU 38 For technical provisions regarding 'Minimum rate of desulphurisation' see Part 5 (Annex V). For 'Compliance with rate of desulphurisation' see Part 6 (Annex V) Directive 2010/75/EU |
Details | ||||||
|
Sulphur dioxide SO2 |
7446-09-5 |
V Annex V (Directive 2010/75/EU) Technical provisions relating to combustion plants |
200 mg/Nm3 |
Waste gases |
Biomass |
Solid |
Part 2 (V) Emission limit values for combustion plants referred to in Article 30(3) |
2 |
100-300 |
Combustion plants using solid or liquid fuels with the exception of gas turbines and gas engines |
00 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correction for the water vapour content of the waste gases and at a standardised O2 content of 6 % for solid fuels, 3 % for combustion plants, other than gas turbines and gas engines using liquid and gaseous fuels and 15 % for gas turbines and gas engines 37 For technical provisions regarding 'Emission monitoring' see Part 3 (Annex V). For 'Assessment of compliance with emission limit values' see Part 4 (Annex V) Directive 2010/75/EU 38 For technical provisions regarding 'Minimum rate of desulphurisation' see Part 5 (Annex V). For 'Compliance with rate of desulphurisation' see Part 6 (Annex V) Directive 2010/75/EU |
Details | ||||||
|
Sulphur dioxide SO2 |
7446-09-5 |
V Annex V (Directive 2010/75/EU) Technical provisions relating to combustion plants |
150 mg/Nm3 |
Waste gases |
Biomass |
Solid |
Part 2 (V) Emission limit values for combustion plants referred to in Article 30(3) |
2 |
> 300 |
Combustion plants using solid or liquid fuels with the exception of gas turbines and gas engines |
00 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correction for the water vapour content of the waste gases and at a standardised O2 content of 6 % for solid fuels, 3 % for combustion plants, other than gas turbines and gas engines using liquid and gaseous fuels and 15 % for gas turbines and gas engines 37 For technical provisions regarding 'Emission monitoring' see Part 3 (Annex V). For 'Assessment of compliance with emission limit values' see Part 4 (Annex V) Directive 2010/75/EU 38 For technical provisions regarding 'Minimum rate of desulphurisation' see Part 5 (Annex V). For 'Compliance with rate of desulphurisation' see Part 6 (Annex V) Directive 2010/75/EU |
Details | ||||||
|
Sulphur dioxide SO2 |
7446-09-5 |
V Annex V (Directive 2010/75/EU) Technical provisions relating to combustion plants |
300 mg/Nm3 |
Waste gases |
Peat |
Solid |
Part 2 (V) Emission limit values for combustion plants referred to in Article 30(3) |
2 |
50-100 |
Combustion plants using solid or liquid fuels with the exception of gas turbines and gas engines |
00 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correction for the water vapour content of the waste gases and at a standardised O2 content of 6 % for solid fuels, 3 % for combustion plants, other than gas turbines and gas engines using liquid and gaseous fuels and 15 % for gas turbines and gas engines 37 For technical provisions regarding 'Emission monitoring' see Part 3 (Annex V). For 'Assessment of compliance with emission limit values' see Part 4 (Annex V) Directive 2010/75/EU 38 For technical provisions regarding 'Minimum rate of desulphurisation' see Part 5 (Annex V). For 'Compliance with rate of desulphurisation' see Part 6 (Annex V) Directive 2010/75/EU |
Details | ||||||
|
Sulphur dioxide SO2 |
7446-09-5 |
V Annex V (Directive 2010/75/EU) Technical provisions relating to combustion plants |
300 mg/Nm3 |
Waste gases |
Peat |
Solid |
Part 2 (V) Emission limit values for combustion plants referred to in Article 30(3) |
2 |
100-300 |
Combustion plants using solid or liquid fuels with the exception of gas turbines and gas engines |
00 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correction for the water vapour content of the waste gases and at a standardised O2 content of 6 % for solid fuels, 3 % for combustion plants, other than gas turbines and gas engines using liquid and gaseous fuels and 15 % for gas turbines and gas engines 37 For technical provisions regarding 'Emission monitoring' see Part 3 (Annex V). For 'Assessment of compliance with emission limit values' see Part 4 (Annex V) Directive 2010/75/EU 38 For technical provisions regarding 'Minimum rate of desulphurisation' see Part 5 (Annex V). For 'Compliance with rate of desulphurisation' see Part 6 (Annex V) Directive 2010/75/EU |
Details | ||||||
|
Sulphur dioxide SO2 |
7446-09-5 |
V Annex V (Directive 2010/75/EU) Technical provisions relating to combustion plants |
250 mg/Nm3 |
Waste gases |
Peat |
Solid |
Part 2 (V) Emission limit values for combustion plants referred to in Article 30(3) |
2 |
100-300 |
Combustion plants using solid or liquid fuels with the exception of gas turbines and gas engines |
In case of fluidised bed combustion |
00 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correction for the water vapour content of the waste gases and at a standardised O2 content of 6 % for solid fuels, 3 % for combustion plants, other than gas turbines and gas engines using liquid and gaseous fuels and 15 % for gas turbines and gas engines 37 For technical provisions regarding 'Emission monitoring' see Part 3 (Annex V). For 'Assessment of compliance with emission limit values' see Part 4 (Annex V) Directive 2010/75/EU 38 For technical provisions regarding 'Minimum rate of desulphurisation' see Part 5 (Annex V). For 'Compliance with rate of desulphurisation' see Part 6 (Annex V) Directive 2010/75/EU |
Details | |||||
|
Sulphur dioxide SO2 |
7446-09-5 |
V Annex V (Directive 2010/75/EU) Technical provisions relating to combustion plants |
150 mg/Nm3 |
Waste gases |
Peat |
Solid |
Part 2 (V) Emission limit values for combustion plants referred to in Article 30(3) |
2 |
> 300 |
Combustion plants using solid or liquid fuels with the exception of gas turbines and gas engines |
00 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correction for the water vapour content of the waste gases and at a standardised O2 content of 6 % for solid fuels, 3 % for combustion plants, other than gas turbines and gas engines using liquid and gaseous fuels and 15 % for gas turbines and gas engines 37 For technical provisions regarding 'Emission monitoring' see Part 3 (Annex V). For 'Assessment of compliance with emission limit values' see Part 4 (Annex V) Directive 2010/75/EU 38 For technical provisions regarding 'Minimum rate of desulphurisation' see Part 5 (Annex V). For 'Compliance with rate of desulphurisation' see Part 6 (Annex V) Directive 2010/75/EU |
Details | ||||||
|
Sulphur dioxide SO2 |
7446-09-5 |
V Annex V (Directive 2010/75/EU) Technical provisions relating to combustion plants |
200 mg/Nm3 |
Waste gases |
Peat |
Solid |
Part 2 (V) Emission limit values for combustion plants referred to in Article 30(3) |
2 |
> 300 |
Combustion plants using solid or liquid fuels with the exception of gas turbines and gas engines |
In case of fluidised bed combustion |
00 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correction for the water vapour content of the waste gases and at a standardised O2 content of 6 % for solid fuels, 3 % for combustion plants, other than gas turbines and gas engines using liquid and gaseous fuels and 15 % for gas turbines and gas engines 37 For technical provisions regarding 'Emission monitoring' see Part 3 (Annex V). For 'Assessment of compliance with emission limit values' see Part 4 (Annex V) Directive 2010/75/EU 38 For technical provisions regarding 'Minimum rate of desulphurisation' see Part 5 (Annex V). For 'Compliance with rate of desulphurisation' see Part 6 (Annex V) Directive 2010/75/EU |
Details | |||||
|
Sulphur dioxide SO2 |
7446-09-5 |
V Annex V (Directive 2010/75/EU) Technical provisions relating to combustion plants |
350 mg/Nm3 |
Waste gases |
Liquid |
Part 2 (V) Emission limit values for combustion plants referred to in Article 30(3) |
2 |
50-100 |
Combustion plants using solid or liquid fuels with the exception of gas turbines and gas engines |
00 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correction for the water vapour content of the waste gases and at a standardised O2 content of 6 % for solid fuels, 3 % for combustion plants, other than gas turbines and gas engines using liquid and gaseous fuels and 15 % for gas turbines and gas engines 37 For technical provisions regarding 'Emission monitoring' see Part 3 (Annex V). For 'Assessment of compliance with emission limit values' see Part 4 (Annex V) Directive 2010/75/EU 38 For technical provisions regarding 'Minimum rate of desulphurisation' see Part 5 (Annex V). For 'Compliance with rate of desulphurisation' see Part 6 (Annex V) Directive 2010/75/EU |
Details | |||||||
|
Sulphur dioxide SO2 |
7446-09-5 |
V Annex V (Directive 2010/75/EU) Technical provisions relating to combustion plants |
200 mg/Nm3 |
Waste gases |
Liquid |
Part 2 (V) Emission limit values for combustion plants referred to in Article 30(3) |
2 |
100-300 |
Combustion plants using solid or liquid fuels with the exception of gas turbines and gas engines |
00 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correction for the water vapour content of the waste gases and at a standardised O2 content of 6 % for solid fuels, 3 % for combustion plants, other than gas turbines and gas engines using liquid and gaseous fuels and 15 % for gas turbines and gas engines 37 For technical provisions regarding 'Emission monitoring' see Part 3 (Annex V). For 'Assessment of compliance with emission limit values' see Part 4 (Annex V) Directive 2010/75/EU 38 For technical provisions regarding 'Minimum rate of desulphurisation' see Part 5 (Annex V). For 'Compliance with rate of desulphurisation' see Part 6 (Annex V) Directive 2010/75/EU |
Details | |||||||
|
Sulphur dioxide SO2 |
7446-09-5 |
V Annex V (Directive 2010/75/EU) Technical provisions relating to combustion plants |
150 mg/Nm3 |
Waste gases |
Liquid |
Part 2 (V) Emission limit values for combustion plants referred to in Article 30(3) |
2 |
> 300 |
Combustion plants using solid or liquid fuels with the exception of gas turbines and gas engines |
00 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correction for the water vapour content of the waste gases and at a standardised O2 content of 6 % for solid fuels, 3 % for combustion plants, other than gas turbines and gas engines using liquid and gaseous fuels and 15 % for gas turbines and gas engines 37 For technical provisions regarding 'Emission monitoring' see Part 3 (Annex V). For 'Assessment of compliance with emission limit values' see Part 4 (Annex V) Directive 2010/75/EU 38 For technical provisions regarding 'Minimum rate of desulphurisation' see Part 5 (Annex V). For 'Compliance with rate of desulphurisation' see Part 6 (Annex V) Directive 2010/75/EU |
Details | |||||||
|
Sulphur dioxide SO2 |
7446-09-5 |
V Annex V (Directive 2010/75/EU) Technical provisions relating to combustion plants |
35 mg/Nm3 |
Waste gases |
In general |
Gas |
Part 2 (V) Emission limit values for combustion plants referred to in Article 30(3) |
3 |
Combustion plants using gaseous fuels with the exception of gas turbines and gas engines |
00 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correction for the water vapour content of the waste gases and at a standardised O2 content of 6 % for solid fuels, 3 % for combustion plants, other than gas turbines and gas engines using liquid and gaseous fuels and 15 % for gas turbines and gas engines 37 For technical provisions regarding 'Emission monitoring' see Part 3 (Annex V). For 'Assessment of compliance with emission limit values' see Part 4 (Annex V) Directive 2010/75/EU 38 For technical provisions regarding 'Minimum rate of desulphurisation' see Part 5 (Annex V). For 'Compliance with rate of desulphurisation' see Part 6 (Annex V) Directive 2010/75/EU |
Details | |||||||
|
Sulphur dioxide SO2 |
7446-09-5 |
V Annex V (Directive 2010/75/EU) Technical provisions relating to combustion plants |
5 mg/Nm3 |
Waste gases |
Liquified gas |
Gas |
Part 2 (V) Emission limit values for combustion plants referred to in Article 30(3) |
3 |
Combustion plants using gaseous fuels with the exception of gas turbines and gas engines |
00 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correction for the water vapour content of the waste gases and at a standardised O2 content of 6 % for solid fuels, 3 % for combustion plants, other than gas turbines and gas engines using liquid and gaseous fuels and 15 % for gas turbines and gas engines 37 For technical provisions regarding 'Emission monitoring' see Part 3 (Annex V). For 'Assessment of compliance with emission limit values' see Part 4 (Annex V) Directive 2010/75/EU 38 For technical provisions regarding 'Minimum rate of desulphurisation' see Part 5 (Annex V). For 'Compliance with rate of desulphurisation' see Part 6 (Annex V) Directive 2010/75/EU |
Details | |||||||
|
Sulphur dioxide SO2 |
7446-09-5 |
V Annex V (Directive 2010/75/EU) Technical provisions relating to combustion plants |
400 mg/Nm3 |
Waste gases |
Low calorific gases from coke oven |
Gas |
Part 2 (V) Emission limit values for combustion plants referred to in Article 30(3) |
3 |
Combustion plants using gaseous fuels with the exception of gas turbines and gas engines |
00 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correction for the water vapour content of the waste gases and at a standardised O2 content of 6 % for solid fuels, 3 % for combustion plants, other than gas turbines and gas engines using liquid and gaseous fuels and 15 % for gas turbines and gas engines 37 For technical provisions regarding 'Emission monitoring' see Part 3 (Annex V). For 'Assessment of compliance with emission limit values' see Part 4 (Annex V) Directive 2010/75/EU 38 For technical provisions regarding 'Minimum rate of desulphurisation' see Part 5 (Annex V). For 'Compliance with rate of desulphurisation' see Part 6 (Annex V) Directive 2010/75/EU |
Details | |||||||
|
Sulphur dioxide SO2 |
7446-09-5 |
V Annex V (Directive 2010/75/EU) Technical provisions relating to combustion plants |
200 mg/Nm3 |
Waste gases |
Low calorific gases from blast furnace |
Gas |
Part 2 (V) Emission limit values for combustion plants referred to in Article 30(3) |
3 |
Combustion plants using gaseous fuels with the exception of gas turbines and gas engines |
00 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correction for the water vapour content of the waste gases and at a standardised O2 content of 6 % for solid fuels, 3 % for combustion plants, other than gas turbines and gas engines using liquid and gaseous fuels and 15 % for gas turbines and gas engines 37 For technical provisions regarding 'Emission monitoring' see Part 3 (Annex V). For 'Assessment of compliance with emission limit values' see Part 4 (Annex V) Directive 2010/75/EU 38 For technical provisions regarding 'Minimum rate of desulphurisation' see Part 5 (Annex V). For 'Compliance with rate of desulphurisation' see Part 6 (Annex V) Directive 2010/75/EU |
Details | |||||||
|
Sulphur dioxide SO2 |
7446-09-5 |
V Annex V (Directive 2010/75/EU) Technical provisions relating to combustion plants |
1000 mg/Nm3 |
Waste gases |
Distillation and conversion residues from the refining of crude-oil for own consumption, alone or with other fuels |
Part 7 (V) Average emission limit values for multi-fuel firing combustion plants within a refinery |
Multi-fuel firing combustion plants within a refinery, with the exception of gas turbines and gas engines |
For combustion plants which were granted a permit before 27 November 2002 or the operators of which had submitted a complete application for a permit before that date, provided that the plant was put into operation no later than 27 November 2003 |
00 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correction for the water vapour content of the waste gases and at a standardised O2 content of 6 % for solid fuels, 3 % for combustion plants, other than gas turbines and gas engines using liquid and gaseous fuels and 15 % for gas turbines and gas engines 20 See Article 40 for details on multi-fuel firing combustion plants 37 For technical provisions regarding 'Emission monitoring' see Part 3 (Annex V). For 'Assessment of compliance with emission limit values' see Part 4 (Annex V) Directive 2010/75/EU 38 For technical provisions regarding 'Minimum rate of desulphurisation' see Part 5 (Annex V). For 'Compliance with rate of desulphurisation' see Part 6 (Annex V) Directive 2010/75/EU |
Details | ||||||||
|
Sulphur dioxide SO2 |
7446-09-5 |
V Annex V (Directive 2010/75/EU) Technical provisions relating to combustion plants |
600 mg/Nm3 |
Waste gases |
Distillation and conversion residues from the refining of crude-oil for own consumption, alone or with other fuels |
Part 7 (V) Average emission limit values for multi-fuel firing combustion plants within a refinery |
Multi-fuel firing combustion plants within a refinery, with the exception of gas turbines and gas engines |
For combustion plants other than combustion plants which were granted a permit before 27 November 2002 or the operators of which had submitted a complete application for a permit before that date, provided that the plant was put into operation no later than 27 November 2003 |
00 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correction for the water vapour content of the waste gases and at a standardised O2 content of 6 % for solid fuels, 3 % for combustion plants, other than gas turbines and gas engines using liquid and gaseous fuels and 15 % for gas turbines and gas engines 20 See Article 40 for details on multi-fuel firing combustion plants 37 For technical provisions regarding 'Emission monitoring' see Part 3 (Annex V). For 'Assessment of compliance with emission limit values' see Part 4 (Annex V) Directive 2010/75/EU 38 For technical provisions regarding 'Minimum rate of desulphurisation' see Part 5 (Annex V). For 'Compliance with rate of desulphurisation' see Part 6 (Annex V) Directive 2010/75/EU |
Details | ||||||||
|
Sulphur dioxide SO2 |
7446-09-5 |
VI Annex VI (Directive 2010/75/EU) Technical provisions relating to waste incineration plants and waste co-incineration plants |
50 mg/Nm3 |
1 d |
Waste gases |
Part 3 (VI) Air emission limit values for waste incineration plants |
1.1 |
Waste incineration plants |
21 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correcting for the water vapour content of the waste gases.They are standardised at 11 % oxygen in waste gas except in case of incineration of mineral waste oil as defined in point 3 of Article 3 of Directive 2008/98/EC, when they are standardised at 3 % oxygen, and in the cases referred to in Point 2.7 of Part 6 39 For technical provisions regarding 'Monitoring of emissions' see Part 6 (Annex VI). For 'Formula to calculate the emission concentration at the standard percentage oxygen concentration' see Part 7 (Annex VI). For 'Assessment of compliance with emission limit values' see Part 8 (Annex VI) Directive 2010/75/EU |
Details | ||||||||
|
Sulphur dioxide SO2 |
7446-09-5 |
VI Annex VI (Directive 2010/75/EU) Technical provisions relating to waste incineration plants and waste co-incineration plants |
100 % of the measured values |
200 mg/Nm3 |
0.5 h |
Waste gases |
Part 3 (VI) Air emission limit values for waste incineration plants |
1.2 |
Waste incineration plants |
21 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correcting for the water vapour content of the waste gases.They are standardised at 11 % oxygen in waste gas except in case of incineration of mineral waste oil as defined in point 3 of Article 3 of Directive 2008/98/EC, when they are standardised at 3 % oxygen, and in the cases referred to in Point 2.7 of Part 6 39 For technical provisions regarding 'Monitoring of emissions' see Part 6 (Annex VI). For 'Formula to calculate the emission concentration at the standard percentage oxygen concentration' see Part 7 (Annex VI). For 'Assessment of compliance with emission limit values' see Part 8 (Annex VI) Directive 2010/75/EU |
Details | |||||||
|
Sulphur dioxide SO2 |
7446-09-5 |
VI Annex VI (Directive 2010/75/EU) Technical provisions relating to waste incineration plants and waste co-incineration plants |
97 % of the measured values |
50 mg/Nm3 |
0.5 h |
Waste gases |
Part 3 (VI) Air emission limit values for waste incineration plants |
1.2 |
Waste incineration plants |
21 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correcting for the water vapour content of the waste gases.They are standardised at 11 % oxygen in waste gas except in case of incineration of mineral waste oil as defined in point 3 of Article 3 of Directive 2008/98/EC, when they are standardised at 3 % oxygen, and in the cases referred to in Point 2.7 of Part 6 39 For technical provisions regarding 'Monitoring of emissions' see Part 6 (Annex VI). For 'Formula to calculate the emission concentration at the standard percentage oxygen concentration' see Part 7 (Annex VI). For 'Assessment of compliance with emission limit values' see Part 8 (Annex VI) Directive 2010/75/EU |
Details | |||||||
|
Sulphur dioxide SO2 |
7446-09-5 |
VI Annex VI (Directive 2010/75/EU) Technical provisions relating to waste incineration plants and waste co-incineration plants |
50 mg/Nm3 |
1 d |
Waste gases |
Part 4 (VI) Determination of air emission limit values for the co-incineration of waste |
2.3 |
Cement kilns co-incinerating waste |
28 All values are standardised at 10 % oxygen 30 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correcting for the water vapour content of the waste gases 39 For technical provisions regarding 'Monitoring of emissions' see Part 6 (Annex VI). For 'Formula to calculate the emission concentration at the standard percentage oxygen concentration' see Part 7 (Annex VI). For 'Assessment of compliance with emission limit values' see Part 8 (Annex VI) Directive 2010/75/EU |
Details | ||||||||
|
Sulphur dioxide SO2 |
7446-09-5 |
VI Annex VI (Directive 2010/75/EU) Technical provisions relating to waste incineration plants and waste co-incineration plants |
400 mg/Nm3 |
1 d |
Waste gases |
Solid fuels with exception of biomass and peat |
Solid |
Part 4 (VI) Determination of air emission limit values for the co-incineration of waste |
3.2.1 |
50-100 |
Combustion plants co-incinerating waste |
For combustion plants referred to in Article 30(2), with the exception of gas turbines and gas engines |
30 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correcting for the water vapour content of the waste gases 31 O2 content 6% |
Details | ||||
|
Sulphur dioxide SO2 |
7446-09-5 |
VI Annex VI (Directive 2010/75/EU) Technical provisions relating to waste incineration plants and waste co-incineration plants |
300 mg/Nm3 |
1 d |
Waste gases |
Peat |
Solid |
Part 4 (VI) Determination of air emission limit values for the co-incineration of waste |
3.2.1 |
50-100 |
Combustion plants co-incinerating waste |
For combustion plants referred to in Article 30(2), with the exception of gas turbines and gas engines |
30 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correcting for the water vapour content of the waste gases 31 O2 content 6% |
Details | ||||
|
Sulphur dioxide SO2 |
7446-09-5 |
VI Annex VI (Directive 2010/75/EU) Technical provisions relating to waste incineration plants and waste co-incineration plants |
200 mg/Nm3 |
1 d |
Waste gases |
Solid fuels with exception of biomass |
Solid |
Part 4 (VI) Determination of air emission limit values for the co-incineration of waste |
3.2.1 |
100-300 |
Combustion plants co-incinerating waste |
For combustion plants referred to in Article 30(2), with the exception of gas turbines and gas engines |
30 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correcting for the water vapour content of the waste gases 31 O2 content 6% |
Details | ||||
|
Sulphur dioxide SO2 |
7446-09-5 |
VI Annex VI (Directive 2010/75/EU) Technical provisions relating to waste incineration plants and waste co-incineration plants |
200 mg/Nm3 |
1 d |
Waste gases |
Solid fuels with exception of biomass |
Solid |
Part 4 (VI) Determination of air emission limit values for the co-incineration of waste |
3.2.1 |
> 300 |
Combustion plants co-incinerating waste |
For combustion plants referred to in Article 30(2), with the exception of gas turbines and gas engines |
30 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correcting for the water vapour content of the waste gases 31 O2 content 6% |
Details | ||||
|
Sulphur dioxide SO2 |
7446-09-5 |
VI Annex VI (Directive 2010/75/EU) Technical provisions relating to waste incineration plants and waste co-incineration plants |
200 mg/Nm3 |
1 d |
Waste gases |
Biomass |
Solid |
Part 4 (VI) Determination of air emission limit values for the co-incineration of waste |
3.2.1 |
50-100 |
Combustion plants co-incinerating waste |
For combustion plants referred to in Article 30(2), with the exception of gas turbines and gas engines |
30 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correcting for the water vapour content of the waste gases 31 O2 content 6% |
Details | ||||
|
Sulphur dioxide SO2 |
7446-09-5 |
VI Annex VI (Directive 2010/75/EU) Technical provisions relating to waste incineration plants and waste co-incineration plants |
200 mg/Nm3 |
1 d |
Waste gases |
Biomass |
Solid |
Part 4 (VI) Determination of air emission limit values for the co-incineration of waste |
3.2.1 |
100-300 |
Combustion plants co-incinerating waste |
For combustion plants referred to in Article 30(2), with the exception of gas turbines and gas engines |
30 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correcting for the water vapour content of the waste gases 31 O2 content 6% |
Details | ||||
|
Sulphur dioxide SO2 |
7446-09-5 |
VI Annex VI (Directive 2010/75/EU) Technical provisions relating to waste incineration plants and waste co-incineration plants |
200 mg/Nm3 |
1 d |
Waste gases |
Biomass |
Solid |
Part 4 (VI) Determination of air emission limit values for the co-incineration of waste |
3.2.1 |
> 300 |
Combustion plants co-incinerating waste |
For combustion plants referred to in Article 30(2), with the exception of gas turbines and gas engines |
30 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correcting for the water vapour content of the waste gases 31 O2 content 6% |
Details | ||||
|
Sulphur dioxide SO2 |
7446-09-5 |
VI Annex VI (Directive 2010/75/EU) Technical provisions relating to waste incineration plants and waste co-incineration plants |
350 mg/Nm3 |
1 d |
Waste gases |
Liquid |
Part 4 (VI) Determination of air emission limit values for the co-incineration of waste |
3.2.1 |
50-100 |
Combustion plants co-incinerating waste |
For combustion plants referred to in Article 30(2), with the exception of gas turbines and gas engines |
30 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correcting for the water vapour content of the waste gases 32 O2 content 3% |
Details | |||||
|
Sulphur dioxide SO2 |
7446-09-5 |
VI Annex VI (Directive 2010/75/EU) Technical provisions relating to waste incineration plants and waste co-incineration plants |
250 mg/Nm3 |
1 d |
Waste gases |
Liquid |
Part 4 (VI) Determination of air emission limit values for the co-incineration of waste |
3.2.1 |
100-300 |
Combustion plants co-incinerating waste |
For combustion plants referred to in Article 30(2), with the exception of gas turbines and gas engines |
30 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correcting for the water vapour content of the waste gases 32 O2 content 3% 33 Emission limit value: linear decrease from 100 to 300 MW of thermal input |
Details | |||||
|
Sulphur dioxide SO2 |
7446-09-5 |
VI Annex VI (Directive 2010/75/EU) Technical provisions relating to waste incineration plants and waste co-incineration plants |
200 mg/Nm3 |
1 d |
Waste gases |
Liquid |
Part 4 (VI) Determination of air emission limit values for the co-incineration of waste |
3.2.1 |
> 300 |
Combustion plants co-incinerating waste |
For combustion plants referred to in Article 30(2), with the exception of gas turbines and gas engines |
30 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correcting for the water vapour content of the waste gases 32 O2 content 3% |
Details | |||||
|
Sulphur dioxide SO2 |
7446-09-5 |
VI Annex VI (Directive 2010/75/EU) Technical provisions relating to waste incineration plants and waste co-incineration plants |
400 mg/Nm3 |
1 d |
Waste gases |
Solid fuels with exception of biomass and peat |
Solid |
Part 4 (VI) Determination of air emission limit values for the co-incineration of waste |
3.2.2 |
50-100 |
Combustion plants co-incinerating waste |
For combustion plants referred to in Article 30(3), with the exception of gas turbines and gas engines |
30 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correcting for the water vapour content of the waste gases 31 O2 content 6% |
Details | ||||
|
Sulphur dioxide SO2 |
7446-09-5 |
VI Annex VI (Directive 2010/75/EU) Technical provisions relating to waste incineration plants and waste co-incineration plants |
300 mg/Nm3 |
1 d |
Waste gases |
Peat |
Solid |
Part 4 (VI) Determination of air emission limit values for the co-incineration of waste |
3.2.2 |
50-100 |
Combustion plants co-incinerating waste |
For combustion plants referred to in Article 30(3), with the exception of gas turbines and gas engines |
30 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correcting for the water vapour content of the waste gases 31 O2 content 6% |
Details | ||||
|
Sulphur dioxide SO2 |
7446-09-5 |
VI Annex VI (Directive 2010/75/EU) Technical provisions relating to waste incineration plants and waste co-incineration plants |
200 mg/Nm3 |
1 d |
Waste gases |
Solid fuels with exception of biomass and peat |
Solid |
Part 4 (VI) Determination of air emission limit values for the co-incineration of waste |
3.2.2 |
100-300 |
Combustion plants co-incinerating waste |
For combustion plants referred to in Article 30(3), with the exception of gas turbines and gas engines |
30 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correcting for the water vapour content of the waste gases 31 O2 content 6% |
Details | ||||
|
Sulphur dioxide SO2 |
7446-09-5 |
VI Annex VI (Directive 2010/75/EU) Technical provisions relating to waste incineration plants and waste co-incineration plants |
300 mg/Nm3 |
1 d |
Waste gases |
Peat |
Solid |
Part 4 (VI) Determination of air emission limit values for the co-incineration of waste |
3.2.2 |
100-300 |
Combustion plants co-incinerating waste |
For combustion plants referred to in Article 30(3), with the exception of gas turbines and gas engines |
30 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correcting for the water vapour content of the waste gases 31 O2 content 6% |
Details | ||||
|
Sulphur dioxide SO2 |
7446-09-5 |
VI Annex VI (Directive 2010/75/EU) Technical provisions relating to waste incineration plants and waste co-incineration plants |
250 mg/Nm3 |
1 d |
Waste gases |
Peat |
Solid |
Part 4 (VI) Determination of air emission limit values for the co-incineration of waste |
3.2.2 |
100-300 |
Combustion plants co-incinerating waste |
For combustion plants referred to in Article 30(3), with the exception of gas turbines and gas engines; In the case of fluidised bed combustion |
30 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correcting for the water vapour content of the waste gases 31 O2 content 6% |
Details | ||||
|
Sulphur dioxide SO2 |
7446-09-5 |
VI Annex VI (Directive 2010/75/EU) Technical provisions relating to waste incineration plants and waste co-incineration plants |
150 mg/Nm3 |
1 d |
Waste gases |
Solid fuels with exception of biomass and peat |
Solid |
Part 4 (VI) Determination of air emission limit values for the co-incineration of waste |
3.2.2 |
> 300 |
Combustion plants co-incinerating waste |
For combustion plants referred to in Article 30(3), with the exception of gas turbines and gas engines; For circulating or pressurised fluidised bed combustion |
30 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correcting for the water vapour content of the waste gases 31 O2 content 6% |
Details | ||||
|
Sulphur dioxide SO2 |
7446-09-5 |
VI Annex VI (Directive 2010/75/EU) Technical provisions relating to waste incineration plants and waste co-incineration plants |
200 mg/Nm3 |
1 d |
Waste gases |
Peat |
Solid |
Part 4 (VI) Determination of air emission limit values for the co-incineration of waste |
3.2.2 |
> 300 |
Combustion plants co-incinerating waste |
For combustion plants referred to in Article 30(3), with the exception of gas turbines and gas engines; For all fluidised bed combustion |
30 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correcting for the water vapour content of the waste gases 31 O2 content 6% |
Details | ||||
|
Sulphur dioxide SO2 |
7446-09-5 |
VI Annex VI (Directive 2010/75/EU) Technical provisions relating to waste incineration plants and waste co-incineration plants |
200 mg/Nm3 |
1 d |
Waste gases |
Biomass |
Solid |
Part 4 (VI) Determination of air emission limit values for the co-incineration of waste |
3.2.2 |
50-100 |
Combustion plants co-incinerating waste |
For combustion plants referred to in Article 30(3), with the exception of gas turbines and gas engines |
30 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correcting for the water vapour content of the waste gases 31 O2 content 6% |
Details | ||||
|
Sulphur dioxide SO2 |
7446-09-5 |
VI Annex VI (Directive 2010/75/EU) Technical provisions relating to waste incineration plants and waste co-incineration plants |
200 mg/Nm3 |
1 d |
Waste gases |
Biomass |
Solid |
Part 4 (VI) Determination of air emission limit values for the co-incineration of waste |
3.2.2 |
100-300 |
Combustion plants co-incinerating waste |
For combustion plants referred to in Article 30(3), with the exception of gas turbines and gas engines |
30 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correcting for the water vapour content of the waste gases 31 O2 content 6% |
Details | ||||
|
Sulphur dioxide SO2 |
7446-09-5 |
VI Annex VI (Directive 2010/75/EU) Technical provisions relating to waste incineration plants and waste co-incineration plants |
150 mg/Nm3 |
1 d |
Waste gases |
Biomass |
Solid |
Part 4 (VI) Determination of air emission limit values for the co-incineration of waste |
3.2.2 |
> 300 |
Combustion plants co-incinerating waste |
For combustion plants referred to in Article 30(3), with the exception of gas turbines and gas engines |
30 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correcting for the water vapour content of the waste gases 31 O2 content 6% |
Details | ||||
|
Sulphur dioxide SO2 |
7446-09-5 |
VI Annex VI (Directive 2010/75/EU) Technical provisions relating to waste incineration plants and waste co-incineration plants |
350 mg/Nm3 |
1 d |
Waste gases |
Liquid |
Part 4 (VI) Determination of air emission limit values for the co-incineration of waste |
3.2.2 |
50-100 |
Combustion plants co-incinerating waste |
For combustion plants referred to in Article 30(3), with the exception of gas turbines and gas engines |
30 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correcting for the water vapour content of the waste gases 32 O2 content 3% |
Details | |||||
|
Sulphur dioxide SO2 |
7446-09-5 |
VI Annex VI (Directive 2010/75/EU) Technical provisions relating to waste incineration plants and waste co-incineration plants |
200 mg/Nm3 |
1 d |
Waste gases |
Liquid |
Part 4 (VI) Determination of air emission limit values for the co-incineration of waste |
3.2.2 |
100-300 |
Combustion plants co-incinerating waste |
For combustion plants referred to in Article 30(3), with the exception of gas turbines and gas engines |
30 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correcting for the water vapour content of the waste gases 32 O2 content 3% 33 Emission limit value: linear decrease from 100 to 300 MW of thermal input |
Details | |||||
|
Sulphur dioxide SO2 |
7446-09-5 |
VI Annex VI (Directive 2010/75/EU) Technical provisions relating to waste incineration plants and waste co-incineration plants |
150 mg/Nm3 |
1 d |
Waste gases |
Liquid |
Part 4 (VI) Determination of air emission limit values for the co-incineration of waste |
3.2.2 |
> 300 |
Combustion plants co-incinerating waste |
For combustion plants referred to in Article 30(3), with the exception of gas turbines and gas engines |
30 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correcting for the water vapour content of the waste gases 32 O2 content 3% |
Details | |||||
|
Sulphur dioxide SO2 |
7446-09-5 |
As SO2 equivalent |
VIII Annex VIII (Directive 2010/75/EU) Technical provisions relating to installations producing titanium dioxide |
Gaseous sulphur dioxide and trioxide |
6 kg/ton |
1 yr |
Waste gases |
Part 2 (VIII) Emission limit values into air |
Installations producing titanium dioxide |
From digestion and calcination, including acid droplets |
40 Emission limit values are given in kg per tonne of titanium dioxide produced, as an annual average |
Details | ||||||
Inland Transport of Dangerous Goods Directive
Inland Transport of Dangerous Goods Directive, Annex I - ADR
This list contains the ADR Dangerous Goods List, as implemented by the European Union's Directive 2008/68/EC. This Directive applies the European Agreements on the international transport of dangerous goods by road (ADR) and inland waterways (ADN), and the regulations concerning the international carriage of dangerous goods by rail (RID). Any specific CAS linked as members for substances where the list refers to finished material/article/compound/component are representative examples, but not exhaustive.
| Name | CAS | Class | Labels | Packing Group | Packaging | UN No. | ADR tank | Classification code | Hazard identification no. | Limited and excepted quantities | Vehicle for tank carriage | Portable tank and bulk containers | Special provisions | Special provisions for carriage | Transport category (Tunnel restriction code) | Notes | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Mixed packing provisions | Special packing provisions | Packing instructions | Tank code | Special provisions | Excepted quantities | Limited quantities | Unit | Instructions | Special provisions | bulk | Loading, unloading & handling | Operation | Packages | Tunnel restriction code | Transport category | ||||||||||||
|
SULPHUR DIOXIDE |
7446-09-5 |
2 |
2.3+8 |
MP9 |
P200 |
1079 |
PxDH(M) |
TA4 TT9 TT10 |
2TC |
268 |
E0 |
AT |
(M) T50 |
TP19 |
CV9 CV10 CV36 |
S14 |
(C/D) |
1 |
1 Not permitted to be carried in limited quantities |
Details | |||||||
Inland Transport of Dangerous Goods Directive, Annex II - RID
This list contains the RID Dangerous Goods List, as implemented by the European Union's Directive 2008/68/EC. This Directive applies the European Agreements on the international transport of dangerous goods by road (ADR) and inland waterways (ADN), and the regulations concerning the international carriage of dangerous goods by rail (RID). Any specific CAS linked as members for substances where the list refers to finished material/article/compound/component are representative examples, but not exhaustive.
| Name | CAS | Class | Labels | Packing Group | UN No. | Classification code | Express parcels | Hazard identification number | RID Tanks | Limited and excepted quantities | Packaging | Portable tanks and bulk containers | Transport category | Special provisions for carriage | Special provisions | Notes | |||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Tank code | Special provisions | Excepted quantities | Units | Limited quantities | Special packaging provisions | Packaging instructions | Mixed packing provisions | Special provisions | Instructions | Loading, unloading & handling | bulk | Packages | |||||||||||||
|
SULPHUR DIOXIDE |
7446-09-5 |
2 |
2.3+8(+13) |
1079 |
2TC |
268 |
PxDH(M) |
TU38 TE22 TE25 TA4 TT9 TT10 TM6 |
E0 |
P200 |
MP9 |
TP19 |
T50 (M) |
1 |
CW9 CW10 CW36 |
1 Not permitted to be carried in limited quantities |
Details | ||||||||
Inland Transport of Dangerous Goods Directive, Annex III - ADN
This list contains the ADN Dangerous Goods List, as implemented by the European Union's Directive 2008/68/EC. This Directive establishes rules for the safe transport of dangerous goods between EU countries by road (ADR) and inland waterways (ADN), and the regulations concerning the international carriage of dangerous goods by rail (RID). Any specific CAS linked as members for substances where the list refers to finished material/article/compound/component are representative examples, but not exhaustive.
| Name | CAS | Class | Labels | Packing Group | UN No. or ID no. | Carriage permitted | Classification code | Equipment required | Limited and excepted quantities | Number of blue cones/lights | Provisions concerning loading, unloading and carriage | Ventilation | Remarks | Special provisions | Notes | |||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Excepted quantities | Limited quantities | Units | Column (11c) | Column (11b) | Column (11a) | |||||||||||||||
|
SULPHUR DIOXIDE |
7446-09-5 |
2 |
2.3+8 |
1079 |
2TC |
PP EP TOX A |
E0 |
2 |
VE02 |
1 Not permitted to be carried in limited quantities |
Details | |||||||||
Marine Environmental Policy Framework Directive
Marine Environmental Policy Framework Directive - Hazardous Substances
This list contains a non-exhaustive inventory of hazardous substances for purposes of the Marine Strategy Framework Directive, especially as it concerns Art. 3(8), and Annexes I and III. The listed substances meet the European Union's definitions as hazardous, as provided on: (1) Table 3 of Annex VI to the CLP Regulation (1272/2008/EC); (2) Annex III of Directive 2000/54/EC (Biological Agents); Candidate List of SVHCs; and REACH Annex XIV (Authorisation List).
| Name | CAS | EU CLP (1272/2008) | EU REACH: List of SVHC | EU_BA Directive 2000/54/EC | EU REACH: Annex XIV |
|---|---|---|---|---|---|
|
sulphur dioxide |
7446-09-5 |
yes |
|||
Medical Devices Directive-repealed
Medical Devices Directive - Hazardous Substances
This list contains hazardous substances in accordance with the Medical Devices Directive's (MDD) design and construction requirements pursuant to Annex I, Part II (7) & (8) (i.e., chemical, physical and biological properties; and infection and microbial contamination). Specifically, the non-exhaustive database is derived from: Table 3 of Annex VI to CLP, REACH Candidate List of SVHCs, and Directive 2000/54/EC's Annex III (Biological Agents list). Please note that Regulation (EU) 2017/745 on medical devices has repealed Directive 93/42/EEC and begun to apply from 26 May 2021. Nevertheless, Article 120 of the Regulation provides for a transitional period allowing medical devices, under specified conditions (e.g., placed on the market prior to 26 May 2021), to continue to comply with the Directive. In accordance with the fourth paragraph of Article 120, this period ends 26 May 2025.
| Name | CAS | EU CLP (1272/2008) | EU_BA Directive 2000/54/EC | EU REACH: List of SVHC |
|---|---|---|---|---|
|
sulphur dioxide |
7446-09-5 |
Press. Gas; Acute Tox. 3; Skin Corr. 1B |
||
Medical Devices Regulation
Medical Devices Regulation - Hazardous Substances
This list contains hazardous substances for purposes of the Medical Devices Regulation (MDR), based on the legislation's Annex I general safety and performance requirements, including for chemical, physical and biological properties. Specifically, the non-exhaustive database is derived from: Table 3 of Annex VI to CLP, REACH Candidate List of SVHCs, and Directive 2000/54/EC's Annex III (Biological Agents list).
| EU CLP (1272/2008) | EU REACH: List of SVHC | EU_BA Directive 2000/54/EC | |
|---|---|---|---|
|
Press. Gas; Acute Tox. 3; STOT SE 1; Skin Corr. 1B |
Details | ||
OELs - Occupational Exposure Limits - 4th list
Occupational Exposure Limits - 4th list - Indicative OELVs
This list contains the indicative occupational exposure limit values (IOELVs) from Commission Directive 2017/164/EU. Member States are required to bring into force the laws, regulations and administrative provisions necessary to comply with this Directive, which establishes values for reference period of eight-hour time weighted average and for a short-term period of 15 minutes. The Directive adds limit values for 27 new chemical agents, and amends 6 existing ones established by earlier directives.
| Name | EC Number | CAS | Long-term Exposure Limit (LTEL) Values | Short-term Exposure Limit (STEL) Values | Expressed As | Physical form | Skin Designation | Miscellaneous Notes | |||
|---|---|---|---|---|---|---|---|---|---|---|---|
| mg/m3 | ppm | mg/m3 | ppm | ||||||||
|
Sulphur dioxide |
231-195-2 |
7446-09-5 |
1.3 mg/m3 |
0.5 ppm |
2.7 mg/m3 |
1 ppm |
2 Commission Directive (EU) 2017/164 of 31 January 2017 establishing a fourth list of indicative occupational exposure limit values pursuant to Council Directive 98/24/EC, and amending Commission Directives 91/322/EEC, 2000/39/EC and 2009/161/EU. |
Details | |||
Pressure Equipment Directive
Pressure Equipment Directive - Group 1 Fluids Hazardous Substances
This list contains a non-exhaustive inventory of hazardous substances based on Article 13(1)(a) of Directive 2014/68/EU, defining Group 1 fluids for purposes of classifying pressure equipment in accordance with the Directive. The list is derived from a subset of the substances with harmonised classifications, as listed on Table 3 of Annex VI to the CLP Regulation 1272/2008/EC.
| Name | CAS | Substance Description | Expressed As | Physical form | Restriction(s) | Index | EC Number | Classifications |
|---|---|---|---|---|---|---|---|---|
|
sulphur dioxide |
7446-09-5 |
016-011-00-9 |
231-195-2 |
STOT SE 1; Acute Tox. 3 (Inhalation) |
||||
Protection of Pregnant and Breastfeeding Workers Directive
Protection of Pregnant and Breastfeeding Workers Directive, Annex I+II
This list contains a non-exhaustive inventory of substances to which pregnant workers and workers who have recently given birth or are breastfeeding may not be exposed. Employers are obligated to prevent the exposure of these workers to any agents that may have adverse health effects on either mother or child. The inventory originates from Table 3 of Annex VI to the CLP.
| Name | CAS | CLP (1272/2008) CMRs | ECCAR Directive 2004/37/EC | EU_BA | PREGW | Notes | |
|---|---|---|---|---|---|---|---|
|
sulphur dioxide |
7446-09-5 |
STOT SE 1 |
Details | ||||
Protection of Young People Directive
Physical, Biological and Chemical Agents & Processes and Work
This list contains biological and chemical agents, in accordance with Art. 7 and points 2 and 3 of the Annex to Directive 94/33/EC, to which young persons (under 18 years of age) may not be exposed at the workplace. The list is a non-exhaustive inventory of such substances based on: 1) agents of risk groups 3 and 4 under Directive 2000/54/EC; 2) Table 3 of Annex VI to the CLP Regulation; 3) and Annex I of Directive 2004/37/EC.
| Name | CAS | EC_YOUNG | ECCAR Directive 2004/37/EC | EU CLP (1272/2008) | EU_BA Directive 2000/54/EC | Notes | |
|---|---|---|---|---|---|---|---|
|
sulphur dioxide |
7446-09-5 |
Acute Tox. 3; STOT SE 1; Skin Corr. 1B |
Details | ||||
Safety and Health of Workers at Work Directive
Safety and Health of Workers at Work Directive - Hazardous Substances
This list contains a non-exhaustive inventory of substances that fall within the scope of the European Union's definition of hazardous chemical and biological substances, as provided on: (1) Table 3 of Annex VI to the CLP Regulation 1272/2008/EC; and (2) Annex III of Directive 2000/54/EC (Biological Agents). The EU's Occupational Safety and Health (OSH) Framework Directive 89/391/EEC applies to risks arising from chemical, physical and biological agents at the workplace.
| Name | CAS | EU CLP (1272/2008) | EU_BA Directive 2000/54/EC |
|---|---|---|---|
|
sulphur dioxide |
7446-09-5 |
Press. Gas; Acute Tox. 3; STOT SE 1; Skin Corr. 1B |
|
Safety and/or Health Signs at Work Directive
Workplace Signs - minimum requirements & signs on containers and pipes
This list contains hazardous substances based on Table 3 of Annex VI to the CLP Regulation 1272/2008/EC. According to the annexes to Directive 92/58/EEC, storage areas and containers containing chemical substances or mixtures that are classified as hazardous according to the CLP Regulation must be duly marked and/or labeled. Directive 92/58/EEC requires employers to ensure proper signage is posted in areas where hazards cannot be avoided or reduced.
| Name | EC Number | CAS | Index | Sustance Description | Danger Symbols | Restriction | Physical form | |
|---|---|---|---|---|---|---|---|---|
|
sulphur dioxide |
231-195-2 |
7446-09-5 |
016-011-00-9 |
Gas cylinder Skull and crossbones Health hazard Corrosion |
Details | |||
WFD - Waste Framework Directive
Waste Framework Directive, Annex III - Waste - Hazardous Properties
This list contains substances that have been assigned hazard property (HP) waste codes 1-15, as defined in terms of the hazard class and category, hazard (H) statement, and/or concentration limits provided in Annex III of the Waste Framework Directive 2008/98/EC. The classifications of the substances listed in the list are based on their harmonised classifications per Table 3 of Annex VI to the CLP Regulation 1272/2008/EC.
| Name | EC Number | CAS | EU CLP (1272/2008) | HP Code | Index |
|---|---|---|---|---|---|
|
sulphur dioxide |
231-195-2 |
7446-09-5 |
Acute Tox. 3 STOT SE 1 Skin Corr. 1B |
HP6 Acute Toxicity: waste which can cause acute toxic effects following oral or dermal administration, or inhalation exposure. HP5 Specific Target Organ Toxicity (STOT)/Aspiration Toxicity: waste which can cause specific target organ toxicity either from a single or repeated exposure, or which cause acute toxic effects following aspiration. HP8 Corrosive: waste which on application can cause skin corrosion. |
016-011-00-9 |